Differences

This shows you the differences between two versions of the page.

--- technical:26.04_ultimate_ubuntu_server_install [2026/06/02 23:09] – mark_scottworld.net
+++ technical:26.04_ultimate_ubuntu_server_install [2026/06/03 02:46] (current) – external edit 127.0.0.1
@@ Line 10: / Line 10: @@
   Select Language - (English UK)
-  Select Keyboard Layout.
+  Select Keyboard Layout. - (English UK)
   Select Ubuntu Server - not the minimized version.
   Check the box for Third Party Drivers (to install things like NVIDIA drivers etc)
+  You can leave the Network Configuration as default - This will set up the network for DHCP (using IPv4 and IPV6) We will be modifying this later.
   Proxy address if you have one.
+  (the install will check the mirror) - once it is on the network.
   Use the entire disk for the OS when asked - it will create the relevent partitions.
+  Leave the checkbox for an LVM group - (no need to Encrypt)
-===== Admin User Configuration =====
+===== Profile Configuration =====
   Your name
@@ Line 23: / Line 27: @@
   Password (and confirmation)
-Skip ubuntu pro (we can do that later)
+===== Upgrade to Ubuntu Pro =====
+Skip ubuntu pro option (we can do that later)
+===== SSH Configuration =====
 Install the SSH server when prompted so you can get remote access.
+===== Install Third Party Drivers ====
+Install any third party drivers if required
+===== Featured server snaps =====
 When asked to install snaps do not select any.
-===== Disk Partitioning =====
+===== Disk Partitioning =====    Move this up above Admin user
 When prompted choose
@@ Line 69: / Line 88: @@
 Make live with
-<code>
   systemctl restart procps.service
+You can check it is applied with
+  cat /proc/sys/vm/swappiness
+===== Allow IP routing internally =====
+  nano /etc/sysctl.d/local.conf
+Add the following line.
+  net.ipv4.ip_forward=1
+Then to load this restart the procps service...
+  systemctl restart procps.service
+===== Network Interface Configuration (Netplan) =====
+Configure a network bridge to present a single interface to the world, this is handy for VMs / VPNs etc. as we only need to reference the bridge. (br0:) - and means we can swap the network interface out without changing all the apps. 26.04 uses netplan to configure its network configuration.
+The following steps will set up a bridge with a static IP address. The interface is br0
+Change to the netplan directory.
+NOTE: You may need to set the DNS server to be the local router - until you have set up BIND, then you can go back and edit this again.
+  cd /etc/netplan
+  nano 00-solaris.yaml  (default netplan config)
+Content of the 00-solaris.yaml
+<code>
+# This is the network config made for solaris
+network:
+  version: 2
+  renderer: networkd
+  ethernets:
+    en01: {}
+  bridges:
+    br0:
+      critical: true
+      dhcp4: false
+      addresses: [ 10.3.200.1/16 ]
+      routes:
+       - to: default
+         via: 10.3.1.1
+      nameservers:
+        search: [ scottworld.net ]
+        addresses: [ 10.3.200.1 ]
+      interfaces: [ en01 ]
+      parameters:
+        stp: false
+      # Disable IPv6
+      dhcp6: false
+      accept-ra: no
+      link-local: []
 </code>
+Disable the cloud network configuration.
+  touch /etc/cloud/cloud-init.disabled
+You can check it with
+  cloud-init status
+Update the permissions on the netplan config to remove the global r/w permissions
+  chomd 600 /etc/netplan/00-solaris.yaml
+Apply the changes
+  netplan --debug apply
+Reboot and check the network configuration with
+  ip addr
+You should have an interface of br0: with the ip you specified.
+<code>
+: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
+    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
+    inet 127.0.0.1/8 scope host lo
+       valid_lft forever preferred_lft forever
+    inet6 ::1/128 scope host noprefixroute
+       valid_lft forever preferred_lft forever
+: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master br0 state UP group default qlen 1000
+    link/ether 52:54:00:eb:cb:22 brd ff:ff:ff:ff:ff:ff
+    altname enx525400ebcb22
+: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
+    link/ether e2:d0:4d:d7:1f:0d brd ff:ff:ff:ff:ff:ff
+    inet 10.3.200.10/16 brd 10.3.255.255 scope global br0
+       valid_lft forever preferred_lft forever
+</code>
-===== User Config =====
+Edit the file
-When prompted create the system login user / password
+  nano /etc/hosts
-The server will install the basics, set up your user / timezone etc. Eventually you will be prompted to Reboot.
-  Reboot Now
+Comment out the entry for 127.0.1.1 and replace it with a Global server value.
+.3.200.1 solaris.scottworld.net solaris